Name : nrf5340_network
description : nRF53 reference description for system-on-chip with dual ARM 32-bit Cortex-M33 microcontrollers
Architecture : (CM33)
revision : r0p4
endian : little
Memory Protection Unit (MPU) : available
Floating Point Unit (FPU) : available
Number of relevant bits in Interrupt priority : 3
name : AAR_NS
description : Accelerated Address Resolver
base address : 0x0
Interrupt (14) AAR_CCM
name : ACL_NS
description : Access control lists
base address : 0x0
name : APPMUTEX_NS
description : MUTEX 0
base address : 0x0
name : APPMUTEX_S
description : MUTEX 1
base address : 0x0
name : CCM_NS
description : AES CCM mode encryption
base address : 0x0
Interrupt (14) AAR_CCM
name : CLOCK_NS
description : Clock management
base address : 0x0
Interrupt (5) CLOCK_POWER
name : CTI_NS
description : Cross-Trigger Interface control. NOTE: this is not a separate peripheral, but describes CM33 functionality.
base address : 0x0
name : CTRLAP_NS
description : Control access port
base address : 0x0
name : DCNF_NS
description : Domain configuration management
base address : 0x0
name : DPPIC_NS
description : Distributed programmable peripheral interconnect controller
base address : 0x0
name : ECB_NS
description : AES ECB Mode Encryption
base address : 0x0
Interrupt (13) ECB
name : EGU0_NS
description : Event generator unit
base address : 0x0
Interrupt (20) EGU0
name : FICR_NS
description : Factory Information Configuration Registers
base address : 0x0
name : GPIOTE_NS
description : GPIO Tasks and Events
base address : 0x0
Interrupt (10) GPIOTE
name : IPC_NS
description : Interprocessor communication
base address : 0x0
Interrupt (18) IPC
name : NVMC_NS
description : Non-volatile memory controller
base address : 0x0
name : P0_NS
description : GPIO Port 0
base address : 0x0
name : P1_NS
description : GPIO Port 1
base address : 0x0
name : POWER_NS
description : Power control
base address : 0x0
Interrupt (5) CLOCK_POWER
name : RADIO_NS
description : 2.4 GHz radio
base address : 0x0
Interrupt (8) RADIO
name : RESET_NS
description : Reset control
base address : 0x0
name : RNG_NS
description : Random Number Generator
base address : 0x0
Interrupt (9) RNG
name : RTC0_NS
description : Real-time counter 0
base address : 0x0
Interrupt (17) RTC0
name : RTC1_NS
description : Real-time counter 1
base address : 0x0
Interrupt (22) RTC1
name : SPIM0_NS
description : Serial Peripheral Interface Master with EasyDMA
base address : 0x0
Interrupt (19) SERIAL0
Interrupt (19) SPIM0_SPIS0_TWIM0_TWIS0_UARTE0
name : SPIS0_NS
description : SPI Slave
base address : 0x0
Interrupt (19) SERIAL0
Interrupt (19) SPIM0_SPIS0_TWIM0_TWIS0_UARTE0
name : SWI0_NS
description : Software interrupt 0
base address : 0x0
Interrupt (26) SWI0
name : SWI1_NS
description : Software interrupt 1
base address : 0x0
Interrupt (27) SWI1
name : SWI2_NS
description : Software interrupt 2
base address : 0x0
Interrupt (28) SWI2
name : SWI3_NS
description : Software interrupt 3
base address : 0x0
Interrupt (29) SWI3
name : TEMP_NS
description : Temperature Sensor
base address : 0x0
Interrupt (16) TEMP
name : TIMER0_NS
description : Timer/Counter 0
base address : 0x0
Interrupt (12) TIMER0
name : TIMER1_NS
description : Timer/Counter 1
base address : 0x0
Interrupt (24) TIMER1
name : TIMER2_NS
description : Timer/Counter 2
base address : 0x0
Interrupt (25) TIMER2
name : TWIM0_NS
description : I2C compatible Two-Wire Master Interface with EasyDMA
base address : 0x0
Interrupt (19) SERIAL0
Interrupt (19) SPIM0_SPIS0_TWIM0_TWIS0_UARTE0
name : TWIS0_NS
description : I2C compatible Two-Wire Slave Interface with EasyDMA
base address : 0x0
Interrupt (19) SERIAL0
Interrupt (19) SPIM0_SPIS0_TWIM0_TWIS0_UARTE0
name : UARTE0_NS
description : UART with EasyDMA
base address : 0x0
Interrupt (19) SERIAL0
Interrupt (19) SPIM0_SPIS0_TWIM0_TWIS0_UARTE0
name : UICR_NS
description : User Information Configuration Registers
base address : 0x0
name : VMC_NS
description : Volatile Memory controller
base address : 0x0
name : VREQCTRL_NS
description : Voltage request control
base address : 0x0
name : WDT_NS
description : Watchdog Timer
base address : 0x0
Interrupt (11) WDT
Is something missing? Is something wrong? can you help correct it ? Please contact us at info@chipselect.org !
This website is sponsored by Embeetle, an IDE designed from scratch for embedded software developers.